Anyone who has cut a few hundred mitered parts by hand knows how the day goes. You set the saw to one angle, make the cut, reset it for the next part, cut again, and somewhere around the fortieth piece you notice a number drifted. The RazorGage AngleMaster is built to take that problem off your plate. It is a semi-automatic miter saw fence system that pushes the material forward and turns the saw to the right angle for every cut, so the operator spends time clamping and cutting instead of chasing settings. If your shop makes frames, trim, windows, doors or any parts with angled ends, this machine deserves a proper look.
What the AngleMaster Actually Does
Think of it as a miter saw with a brain. A regular saw only knows what you tell it, one cut at a time. The RazorGage AngleMaster pairs a programmable positioner with an angle saw that adjusts itself, and the software ties both together. According to the manufacturer’s own description, it handles both the leading and the trailing angle of a part automatically. That is the detail that matters most. A part with two different end angles normally means two manual setups. Here, the machine does that work between cuts.
The system runs on RazorGage’s AngleMaster software with AutoList built in. AutoList is what lets the machine work through a list of parts in order, without someone standing there punching numbers into a keypad before every single cut.
How a Cut Works on the Shop Floor
The workflow is simple enough that a new operator can pick it up fast. You either pick a cutlist that the office has already sent to the machine, or you type in the leading angle, trailing angle, length and width for a single part. The positioner moves the stock forward and rotates the saw to the leading angle. The operator checks the clamps, makes sure the material sits against the fence and the pusher, and cycles the saw.
The part that still needs a human
This is a semi-automatic system, and that is on purpose. After the first cut, the operator clears any small drops that could jam, then taps DONE on the touchscreen. The positioner then advances the material again and swings the saw to the trailing angle. Then you clamp and cut once more. Honestly, I like that the person stays in the loop here. Clearing the table and watching the cut is the part where experience matters, and the machine leaves that to you.
Cutlists, Software and the Office Connection
A lot of the real time saving is in the software. Cutlists can be sent straight to the AngleMaster computer over Wi-Fi or a wired Ethernet cable, so the office does not have to walk printouts out to the floor. You can optimize a list at the machine, or run lists that were already optimized in other popular software. Sorting cutlists right at the saw is also possible, which helps when one job needs to come off the machine in a certain order.
The computer is a Windows PC with a large colour touchscreen, and the software is compatible with most label printers. If you want labelled parts coming off the saw, a label printer option is available.
Hardware and Setup Details Worth Knowing
The saw itself is a 5.5 horsepower unit, available for 230 or 460 volt three-phase power. So your shop needs three-phase supply before you start planning, and that is worth checking early. The standard table top is PVC, and you can ask for steel or PVC rollers if your material needs them. One planning note from a dealer listing: the positioner stroke is two feet longer than the longest stock you plan to load, so tell them the longest piece you run when you order.
Installation and saw system training are included in the price quotes listed by at least one dealer, which takes some of the nervousness out of buying a machine like this. Pricing is quote-based, so you will need to call.
Measuring Angles Properly
Here is something that does not get talked about enough. Your machine can only be as good as the angles you feed it. RazorGage ran into this while building the AngleMaster, because they could not find a good tool for measuring angles accurately. So they made their own digital angle measurement device, accurate to one hundredth of a degree. It comes with a 1-2-3 block for calibration and a padded travel case. If you plan to cut tight miters where the joint has to close without gaps, a tool like this is a smart add-on.
Who Should Look at This Machine
The AngleMaster makes the most sense for shops that cut many angled parts in repeat jobs, and where mistakes in angles mean wasted material and rework. Picture a small shop making picture frames and a larger one running window and door components; the benefit is similar in both. You get repeatable angles, fewer manual setups, and a cutlist that drives the work.
RazorGage has been building programmable saw stops, automatic pushers and optimizing saw systems since 2001, so this is not a new company experimenting with a new idea.
Conclusion
Angle cutting does not need to be slow or full of second-guessing. The AngleMaster moves the repetitive setup work onto the machine and keeps the operator in charge of the final cut. If your work also involves straight cuts with defect scanning, it is worth looking at the RazorOptimal as well, since it scans material for defects and optimizes parts around them. For angled work, though, the AngleMaster is the one to start with. Get in touch with the RazorGage team, tell them what you cut and how much, and ask for a quote that fits your shop.
Frequently Asked Questions
What is the RazorGage AngleMaster?
The RazorGage AngleMaster is a semi-automatic programmable angle saw system. It advances your material and rotates the miter saw to the correct leading and trailing angles for each part.
Is the AngleMaster fully automatic?
No. It is semi-automatic. The operator still checks the clamps, cycles the saw, clears small drops from the table and confirms each step on the touchscreen.
How do cutlists get to the machine?
You can send them over Wi-Fi or an Ethernet cable. You can also type the angles, length and width in by hand for a single part.
What power does the saw need?
The saw is a 5.5 horsepower unit that runs on 230 or 460 volt three-phase power, so check your shop supply before ordering.
How is the AngleMaster different from the RazorOptimal?
The AngleMaster is built for angled cuts. The RazorOptimal is an optimizing saw that scans material for defects and arranges parts around them, with options like pocket hole drilling.
Contact Us
Address: 57006 241st Street, Ames, IA 50010
Phone: 515.232.3188
Email: sales@RazorGage.com
Comments (0)